For Canon R5C. It does not support 8K 60P auto focus, but support 8K 30P auto focus. Please note that do not use this dummy battery on the SmallHD or Blackmagic camera, do not use it for the others that we do not mention. (About the other details, welcome to contact us) | Plug A: E6 Dummy Battery (DR E6); Plug B: D-tap. | Please ensure that the output of the power source does not exceed 16.8V. The output is about 8V. Please follow the below installation steps, which is better for your device and dummy battery cable: Firstly plug the D-Tap into the battery, then load the dummy battery into the battery compartment, and finally turn on your device. | Min Length: 30cm(12inches). Max Length: 1m(39.4inches). We can customize cables with other length, if you need custom cables, please send a message to us before placing the order. | Every cable was tested to ensure that there are no short circuit, no potential breakdown problems before shipping. Please contact us if the cable you received is defective or doesn’t work. We will solve the problems properly or send you a new replacement at once.

With this cable, you can power Canon 5D mark II 7D 60D from the 12v 2pin output on Arri Alexa XT. | It is for Canon 5D mark II 7D 60D. | Plug A: Lanparte LP E6 Dummy Battery; Plug B: Rotatable Right Angle 0B 2 Pin Male. | Alvin's Rotatable Right Angle Plug can be rotated at any 45 degrees to meet a variety of wiring needs. Please note, before rotating, you need to unlock the nut first, if you don't know how to do, please contact us. | Cable Length: 20 inches (50cm). We can customize cables with other length, if you need custom cables, please send a message to us before placing the order.

This cable is designed for powering Teradek Bond| SmallHD Monitor from any standard 0B 2 pin(pin1 GND, pin2+) power output socket. And it is more flexible and softer than regular version, making it easier to adapt the cable to device layouts. | It is with special custom design Alvin's Rotatable Right Angle 2 pin connector, which can be rotated at any directions (0/45/90/135/180/225/270/315 degrees direction), default 3 o'clock direction (45 degrees). Please note, if you want to rotate it, please unlock the nut first, then you can rotate it, if you don't know how to do, please contact us. | Plug A: Rotatable Right Angle 2 Pin Male. Plug B: Straight 2 Pin Male. | Cable Length: 45cm|18 inches. We can customize cables with other length, if you need custom cables, please send a message to us before making the order. | Every cable was tested to ensure that there are no short circuit, no potential breakdown problems before shipping. Please contact us if the cable you received is defective or doesn’t work. We will solve the problems properly or send you a new replacement at once.

This cable is specially designed for the Blackmagic Pocket Cinema Camera 4K 6K camera (need to plug in DC 8V interface hole), to increase shoot time and to reduce battery charging downtime. | There are two DC output ports whose output voltage are respectively 8V and 12V, allowing you to use for other devices, such as video monitors, LED lights, etc. Please ensure to use the correct rated voltage and current of the electrical equipment. | With a 1/4" manual screw and hot shoe mount, you can easily install the battery plate on your camera or other device. There is a power switch to control, please turn off it when the temparature is too high. | What's in the package: NP-F battery plate×1, Min length 12 inches BMPCC-DC cable×1,12 inches DC-DC cable×1, 1/4” hot shoe mount×1（Fix the battery plate on the device）. | Every cable was tested to ensure that there are no short circuit, no potential breakdown problems before shipping. Please contact us if the cable you received is defective or doesn’t work. We will solve the problems properly or send you a new replacement at once.

Power Cable for Arri|RED|Steadicam Rigs|Z CAM E2 Flagship E2-S6 E2-F6 E2-F8 Camera to Tilta Nucleus M | Plug A: Straight 2 Pin Male. | Plug B: Nucleus Straight 7 Pin Male. | Cable Length: 15 Inches/38cm (Maximun length: 39in/1m). We can customize cables with other length, if you need custom cables, please send a message to us before placing the order. | Every cable was tested to ensure that there are no short circuit, no potential breakdown problems before shipping. Please contact us if the cable you received is defective or doesn’t work. We will solve the problems properly or send you a new replacement at once.

This is a SDI-Port-Protection-Cable to prevent users from damaging the SDI port due to incorrect operational procedures. | Plug A: Original BNC Male. Plug B: Right Angle BNC Female with SDI Protector. | Please note, that SDI isolators can reduce signal quality and/or maximum cable length. This cable is transmitted via frenquency, which can block the current of the shielding layer, and protect against SDI damage. And generally, when the signal is reduced, it can be used transmitted in 2K|1080p, and cannot be used for transmission in 4K/8K . | Color: Red. Cable length: 8inches/ 20cm. We can customize cables with other length, if you need custom cables, please send a message to us before placing the order. | Every cable was tested to ensure that there are no short circuit, no potential breakdown problems before shipping. Please contact us if the cable you received is defective or doesn't work. We will solve the problems properly or send you a new replacement at once.

Power the Z CAM EVF through the 12V 2 Pin Aux . Also for Teradek Bond| ARRI Alexa Camera| SmallHD 702 Bright (SmallHD's Faux LP-E6 Adapter) from any standard 0B 2 pin power output socket. | This cable is with special custom design Alvin's Rotatable Right Angle 2 pin connector, which can be rotated at any directions (0/45/90/135/180/225/270/315 degrees direction), default 9 o'clock direction (270 degrees).Please note,if you want to rotatate it, please unlock the nut first, then you can rotate it, if you don't know how to do, please cotnact us. | Plug A: Right Angle Rotatable 2 Pin male connector. Plug B: Standard Right Angle 2 Pin male connector. | Cable Length: 30cm (about 12 inches). We can customize cables with other length, if you need custom cables, please send a message to us before making the order. | Every cable was tested to ensure that there are no short circuit, no potential breakdown problems before shipping. Please contact us if the cable you received is defective or doesn’t work. We will solve the problems properly or send you a new replacement at once.

Feed timecode to Tentacle Sync from Sound Devices Recorder using standard 0B 5-pin connector.(The signal direction to flow from the 5-pin to the 1/8" TRS) | It is compatible with ARRI Alexa or Sound Devices 888/ 702T/ 744T/ 788T/ 664/ 633 or other devices that using a 5 pin connector into jam-sync Tentacle. (Please don't use it for other devices that we have not mentioned before contacting us for confirmation, thank you.) | Plug A: Right Angle 3.5mm TRS; Plug B: Right Angle 0B 5 Pin Male (better fit the bag). | Cable Length: 15cm (6inches). We can customize cables with other length, please send a message to us before making the order. | Every cable was tested to ensure that there are no short circuit, no potential breakdown problems before shipping. Please contact us if the cable you received is defective or doesn't work. We will solve the problems properly or send you a new replacement at once.