The output features is an open collector and coupler parameters are guaranteed over the temperature range from -40℃~5℃. | The internal shield provides a guaranteed Common Mode Transient Immunity (typical) 10KV/μs. | High Speed: 10MBd | Check description below for links to instructions and datasheets! | Skill Level: Assembled and Tested

Access the pins on your car's OBDII connector | Hack your car | Packaging : - ; Manufacturer : SparkFun ; Rohs : 1 | Cnhts : 8543709991 ; Hts Code : 8544429090 ; Mxhts : 85444204 | Product Type : Daughter Cards & Oem Boards ; Subcategory : Embedded Solutions ; Taric : 8544429090

Voltage: 5 to 12V | JST connector | Simple Motion Sensor

MCP73833 | Complete Linear Charge Management Controller Integrated Pass Transistor Integrated Current Sense Integrated Reverse Discharge Protection | Constant Current / Constant Voltage Operation with Thermal Regulation Programmable Charge Current: 1A Maximum | Preconditioning of Deeply Depleted Cells Selectable Current Ratio Selectable Voltage Threshold | Supply Voltage: 3.75V-6V

PCA9306 dual bidirectional voltage-level translator | low voltage side: 1.2V to 3.3V (VREF1) | high voltage side: 1.8V to 5V (VREF2) | I2C - SMBus | Bidirectional

A unique entry into SparkFun's GNSS catalog featuring the ZED-F9T GNSS receiver from u-blox. The ZED-F9T provides up to 5 nanosecond timing accuracy under clear skies with no external GNSS correction making it perfect for applications where timing accuracy is imperative. | Need an extremely accurate time reference to maximize the efficiency of your IoT network of 5G devices? The GNSS Timing Breakout - ZED-F9T could be the perfect solution. | Concurrent reception of GPS, GLONASS, Galileo and BeiDou constellations; Receives L1/L2/E5b bands; Voltage: 5V or 3.3V (all logic is 3.3V); Current: 68mA - 130mA (varies depending on operating conditions and constellations) | Fix Acquisition: ~24s (Cold) / 2s (Hot); Time Pulse Signal Accuracy: Absolute Timing Mode: 5ns and Differential Timing Mode (with correction data): 2.5ns; Time Pulse Signal Frequency: 0.25Hz to 25MHz | Time Pulse Signal Jitter: ±4ns; Horizontal Position Accuracy: 2.0m; Max Altitude: 80km (49.7 miles); Max Velocity: 500m.s (118mph); I2C Address: 0x42; 2x Qwiic Connectors; Note: Breakout board only; cables, antenna, and microcontroller need to be purchased separately.

Supports concurrent reception of four GNSS maximizes position accuracy in challenging conditions increasing precision and decreases lock time | 92-channel u-blox M9 engine GNSS receiver. Receive signals from the GPS, GLONASS, Galileo, and BeiDou constellations | Onboard rechargeable battery, you'll have backup power enabling the GPS to get a hot lock within seconds! | Detects jamming and spoofing events and can report them to the host, so that the system can react to such events. | Integrated Chip Antenna. Supports NMEA, UBX, and RTCM protocols over UART or I2C interface

72-Channel GNSS Receiver. 2.5m Horizontal Accuracy. 30Hz Max Update Rate. Time-To-First-Fix: Cold: 26s, Hot: 1.5s | Max Altitude: 50,000m. Max G: ≤4. Max Velocity: 500m/s. Velocity Accuracy: 0.5m/s. Heading Accuracy: 1 degrees. Time Pulse Accuracy: 30ns | Built-In Accelerometer and Gyroscope. 3.3V VCC and I/O. Current Consumption: ~29mA Continuous Tracking, Default Concurrent Mode | Software Configurable: Geofencing, Odometer, Spoofing Detection, External Interrupt, Pin Control, Low Power Mode, Many others! Compatible with Arduino! | Note: This product requires an antenna: Be sure to pick a suitable U.FL antenna for your project. Integrated U.FL connector for use with antenna of your choice

Frequency Range: 1558 - 1615MHz | LNA Voltage: 3.3 to 15VDC | Primary Antenna Gain: 4dB | LNA Gain: 38dB | Termination Connector: SMA

Concurrent reception of GPS, GLONASS, Galileo and BeiDou. Receives both L1C/A and L2C bands, Time to First Fix: 25s (cold), 2s (hot) | Voltage: 5V or 3.3V but all logic is 3.3V. Current: 68mA - 130mA (varies with constellations and tracking state). Weight: 6.8g. Dimensions: 43.5mm x 43.2mm (1.71in x 1.7in). 2x Qwiic Connectors | This product is compatible with u-blox PointPerfect & includes a redemption code for 1-month of unlimted access for a single device. Take your precision to the next level with the PointPerfect GNSS augmentation service. As of January 2023, a promotional card with a 16 digit referral code is included with your SparkFun packaging. | Max Navigation Rate: PVT (basic location over UBX binary protocol) - 25Hz. RTK - 20Hz. Raw - 25Hz | Horizontal Position Accuracy: 2.5m without RTK. 0.010m with RTK. Max Altitude: 50km (31 miles). Max Velocity: 500m/s (1118mph)

Note: Module only. A Carrier board will need to be purchased separately for this board to function. | The SparkFun MicroMod Teensy Processor leverages the awesome computing power of the NXP iMXRT1062 chip and pairs it with the M.2 MicroMod connector to allow you to plug it into your choice of compatible MicroMod Carrier Board. | With the M.2 MicroMod connector, connecting your Teensy Processor is a breeze. Simply match up the key on your processor's beveled edge connector to the key on the M.2 connector and secure it with a screw (included with all Carrier Boards). Adding a Teensy to your desired project has never been easier! | Features: USB Device up to 480Mbit/sec: Capable of enumerating as a USB keyboard, mouse, joystick, MIDI, audio, and more. USB Host up to 480Mbit/sec: Capable of interfacing to USB flash drives, mice, keyboards, and more | Additional Features: 7x Serial Ports, 2x SPI, 4x I2C Bus, 1x CAN-Bus, 1x I2S Digital Audio, 1x SDIO for SD, 2x Dedicated Analog Pins (Up to 14 available for use), 2x Dedicated PWM Pins (Up to 22 available for use)

This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. | This Breakout Features: Fully equipped with SP3485 RS-485 transceiver and supporting components. Operates from a single +3.3V supply. Interoperable with +5.0V logic. | Also Features: RS-485 input/output broken out to RJ-45 connector, 3.5mm screw terminal, and 0.1" pitch header. Driver/Receiver Enable connected to RTS line. -7V to +12V Common-Mode Input Voltage Range. Allows up to 32 transceivers on the serial bus. Driver Output Short-Circuit Protection. 0.9x1.0". | The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount of power and can operate from a single +3.3VDC supply. | This breakout board includes the SP3485 RS-485 transceiver, filter capacitor, and other components shown on the schematic. We've broken out the RS-485 output to three different connections: (1) an RJ-45 connector, (2) a 3-pin 3.55mm screw terminal, and (3) a 3-pin 0.1" pitch header; none of these output connectors come populated.

Seamlessly pass serial data to and from your (Arduino-Compatible) board wirelessly! Kit allows for simple serial cable replacement. | Transmit remote sensor data, update a scoreboard from your computer, or drive a robot from your keyboard! | XBee 3 not only handles 802.15.4, and ZigBee, but also BLE protocols. Talk to the modules over UART or SPI as well. | 3.3V power regulation and level shifting on-board. With a 200ft indoor range, or 4000ft outdoor/line-of-sight range. | Set up a mesh network to talk to or communicate with various devices around your house, work, or other area.