[Size] The thread size of 8AN is 3/4-16 UNF. The AN side is sealed by a 37 degree angle. | [Application] The swivel fitting is only work with stainless braided and nylon braided hose . | [Material] Made of aluminum alloy 6061-T6. | [Parameter] Max Working Pressure: 1500PSI. Working Temperature Range: -65℉ to 252℉ (-53℃ to 122℃). | [Feature] 360° Swivel design for easy assembly. It can be reused and recycle.

[Size] The thread size of 8AN is 3/4-16UNF. The AN side is sealed by a 37 degree angle. | [Application] The swivel fitting is only work with stainless braided and nylon braided hose. | [Material] Made of aluminum alloy 6061-T6. | [Parameter] Max Working Pressure: 1500PSI. Working Temperature Range: -40℉ to 248℉ (-40℃ to 120℃). | [Feature] 360° Swivel design for easy assembly. It can be reused and recycle.

[Size] Inner hole diameter: 0.63 inch (16mm). Fit for clamping and mounting 8AN fuel line. | [Material] Aluminum alloy 6061-T6. | [Function] It can use to secure and separate transmission lines to keep your project clean and organized. | [Application] Fuel hose separator clamp wildly used in fuel hose, oil line, brake line, gas line, water pipe etc. | [Note] Five sizes of hose mounting clamps available, please measure the OD of your hose before purchasing .

Size: AN8 to 1/2" NPT, the thread size of 8AN is 3/4-16 UNF. | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

Size: AN8 to 1/2" NPT, the thread size of 8AN is 3/4-16 UNF. | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing: The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended.

Size: AN8 to 1/4" NPT, the thread size of 8AN is 3/4-16 UNF. | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

[Size] AN8 to 1/4" pipe, the thread size of 8AN is 3/4-16 UNF. | [Material] Made of aluminum alloy 6061-T6, anodized black surface, bright appearance, anti-corrosion. | [Sealing] The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | [Application] Widely used in fuel system, cooling system, power steering system, etc. | [Notice] To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

Size: AN8 to 1/8" NPT, the thread size of 8AN is 3/4-16 UNF. | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

[Size] AN8 to 3/4" pipe, the thread size of 8AN is 3/4-16 UNF, Degree: 90 degree elbow | [Material] Made of aluminum alloy 6061-T6, anodized black surface. | [Sealing] The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | [Application] Widely used in fuel system, cooling system, power steering system, etc. | [Notice] To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

Size: AN8 to 3/8" NPT, the thread size of 8AN is 3/4-16 UNF. | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

Size: AN8 to 3/8" NPT, the thread size of 8AN is 3/4-16 UNF. | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in cars' fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended.

8AN braided fuel line kit widely used as transmission oil cooler line, fuel return line, fuel supply line, coolant fluid hose, fuel gauges line, vacuum line, turbo cooler line, oil feed line. | Nylon and stainless steel braided fuel hose kit can be compatible with transmission fluid, oil, race gas, vacuum, hydraulic fluid, diesel and fuel. | Maximum working pressure: 750psi. Bursting pressure: 2250psi. Temperature range: -40℉ to 257℉. | Package includes: 10pcs 8an black&red swivel hose ends (4pcs straight, 2pcs 45degree, 2pcs 90degree, 2pcs 180degree), 2pcs 8an hose separator clamp and 8an braided fuel line (Length: 20 Feet). Hose ID: 0.41". Hose OD: 0.65inch. | 8AN fuel hose is made of cpe rubber inner, with a layer of 304 steel wire and nylon outer braid; the hose fittings are made of aluminum alloy.

[Size] Thread Size of 8AN PTFE Fitting is 3/4-16UNF. | [Application] The PTFE Hose End only work with PTFE fuel line. | [Parameter] Working pressure: 1500PSI. Temperature range: -65°F-252°F. | [Seal] The AN side is sealed by a 37 degree angle. | [Material and Feature] Made of aluminum alloy 6061-T6. 360° Swivel design for easy assembly.

[Size] Thread Size of 8AN PTFE Fitting is 3/4-16UNF. | [Application] The PTFE Hose End only work with PTFE fuel line. | [Parameter] Working pressure: 1500PSI. Temperature range: -65°F-252°F. | [Seal] The AN side is sealed by a 37 degree angle. | [Material and Feature] Made of aluminum alloy 6061-T6. 360° Swivel design for easy assembly.

[Size] 8AN to 1/2 inch barb, and thread size of 8an is 3/4-16UNF. | [Application] The barb fitting only work with rubber fuel line. | [Parameter] Max working pressure: 1500PSI; Temperature range: -40℉ to 248℉. | [Material] Made of aluminum alloy 6061-T6. | [Installation] Easy to install, it is recommended to use clamps to enhance sealing.

The female AN8 swivel fittings are made of lightweight aluminum alloy 6061-T6 material for strong strength and good durability. Black anodized for great appearance and anti-corrosion, superior thread strength. Max Working Pressure: 1000psi. Working Temperature Range: -65℉ to 252℉ （-53℃ to 122℃). Can be suitable for competition applications where reduced weight is needed. | 8AN swivel hose end is widely used in oil/ fuel/ water/ fluid/ airline etc. Connect oil gas line, braided fuel line ,clutch hose,turbo line etc. Our swivel fitting is work with nylon braided fuel hose . They are not compatible with PTFE hose, E85, rubber hose . | These new full flow swivel hose ends swivel 360° to allow for a quick alignment of the hose after assembly.Swivel hose end can be reused and recycle if you do not want them to stay in the original place. | Weld-free construction that gives better fluid flow and integrity over the normal brazed together hose ends. Swivel fittings are easy to use and don't require special equipment. We normally recommend a bit of assembly lube to help prevent any galling. | EVIL ENERGY provide this product have 3-month warranty.We value your shopping experience and strive to offer a high-quality product and service.

Size: 8AN flare to 1/2" NPT, the thread size of 8AN is 3/4-16 UNF, Degree: 90 degree elbow | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

Size: 8AN flare to 1/2" NPT, the thread size of 8AN is 3/4-16 UNF, Degree: 90 degree elbow | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

Size: 8AN flare to 1/4" NPT, the thread size of 8AN is 3/4-16 UNF, Degree: 90 degree elbow | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

Size: 8AN flare to 1/4" NPT, the thread size of 8AN is 3/4-16 UNF, Degree: 90 degree elbow | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

Size: 8AN flare to 3/8" NPT, the thread size of 8AN is 3/4-16 UNF, Degree: 90 degree elbow | Material: Made of aluminum alloy 6061-T6, anodized black surface. | Sealing：The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | Application: Widely used in fuel systems, cooling systems, power steering systems, etc. | Notice: To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

[Size]8AN flare to 3/8" NPT, the thread size of 8AN is 3/4-16 UNF, Degree: 90 degree elbow. | [Material] Made of aluminum alloy 6061-T6, anodized black surface. | [Sealing] The AN side of the flare is sealed by a 37 degree angle and the NPT thread side is sealed by a 60 degree tapered thread. | [Application] Widely used in fuel system, cooling system, power steering system, etc. | [Notice] To ensure no leakage at the NPT end, sealant or PTFE tape is strongly recommended. Easy installation and removal with wrench.

Material: Made of aluminum alloy check valve,304 stainless steel spring,NBR rubber gasket and O-ring. | Size: 9/16inch (14mm) OD. | Parameter: Min upstream pressure:0.2bar(2.9psi),working pressure range: 0.2-6bar (2.9-87psi),operating temperature range: -22℉ to 266℉. | Medium: Applicable to water, petrol, diesel, gas, oil, air, and other fluids.(Methanol is not recommended) | Application: The fuel line check valve is widely uesd in carburetors and low pressure fuel systems.

Material: Made of aluminum alloy check valve,304 stainless steel spring,NBR rubber gasket and O-ring. | Size: 9/16inch (14mm) OD. | Parameter: Min upstream pressure:0.2bar(2.9psi),working pressure range: 0.2-6bar (2.9-87psi),operating temperature range: -22℉ to 266℉. | Medium: Applicable to water, petrol, diesel, gas, oil, air, and other fluids.(Methanol is not recommended) | Application: The fuel line check valve is widely uesd in carburetors and low pressure fuel systems.

【Adjustable range】This wrench size can be adjusted to 3AN, 4AN, 6AN, 8AN, 10AN and 12AN. | 【Material】 It's made of lightweight 6061-T6 aluminum . Recommended for aluminum fitting, easy to damage for other materials. Advice:wrap the wrench's jaws with electircal tape to better protect the fitting &wrench. | 【Advantage】Multisize in one /Contact of four opposite sides | 【Size】length: 6.89 inch/17.5 cm,width: 2.5 inch/6.36 cm,thickness:0.52 inch/1.35cm. | 【Warranty】EVIL ENERGY provide this product have 3-month warranty. Any problem you might have ,please feel free to contact us via Amazon message.

[Universal]It can be applied to most cars, making sure there's enough room for Installation. | [Size] Hose length: 31.5in / 0.8m,hose ID:3/8",hose OD:2/3".The thread of the inlet and outlet is M16*1.5.Capacity:300ML. | [Baffled] The baffle is disassembled in a rotary manner, adding an appropriate amount of steel balls can increase the surface area of steam condensation and more effectively catch oil. | [Note] When the temperature outside reaches the freezing point or below, the crank vent system will generate a much greater amount of moisture which can present a risk of freezing. Please clean your oil catch can on a weekly or install the original PCV hose. | Oil Catch Can with or without Breather Filter: Install the oil catch can with breather filter for pre-PCV cars as a vent system or without breather filter in line between PCV hoses as a seal can.

[Universal]It can be applied to most cars, making sure there's enough room for Installation. | [Size] Hose length: 31.5in / 0.8m,hose ID:3/8",hose OD:2/3".The thread of the inlet and outlet is M16*1.5.Capacity:300ML. | [Baffled] The baffle is disassembled in a rotary manner, adding an appropriate amount of steel balls can increase the surface area of steam condensation and more effectively catch oil. | [Note] When the temperature outside reaches the freezing point or below, the crank vent system will generate a much greater amount of moisture which can present a risk of freezing. Please clean your oil catch can on a weekly or install the original PCV hose. | Oil Catch Can with or without Breather Filter: Install the oil catch can with breather filter for pre-PCV cars as a vent system or without breather filter in line between PCV hoses as a seal can.

Size: joins 2.25" OD pipe to 2.25" ID pipe, width of strap: 2.94inch /74.82mm. | Application: Lap joint clamp is a simple, effective way to connect exhaust system components such as pipes, mufflers, catalytic converters etc. | Advantage: No welding design, easy to install or remove. | Material: 304 stainless steel band, zinc-plated M10 bolt and nut, steel gasket, aluminum alloy I-block. | Feature: The band clamps make the force of 360 evenly distributed, provides a seal and prevents material deformation.Torque: 63 N·m.

[Size] Joins male/female flange 2.5" ID to 2.5" pipe. T-Bolt thread size: M8*1.25. | [Advantage] V-band clamp is easy to install and remove. The male and female flanges can be connected more stable, and provide a good seal with uniform pressure at the flange. | [Feature] Male and female flanges are sealed without gaskets to ensure proper alignment of the flanges inside the clamp for easy installation. | [Material] 304 Stainless steel clamp and flanges; 304 stainless steel for long durability and reliability, corrosion resistance and high-temperature resistance. | [Application] Compatible for exhaust system, turbocharger, downpipe, muffler etc.

What you will get: you will get an evil eye car hanging ornament, beautiful appearance can bring different effects from your furniture atmosphere, beautiful appearance can also bring you a good mood | Reliable material: this evil eye jewelry is made of crystal beads, plastic and alloy; It is not easy to fade or deform; It meets your needs for long-term use and brings you different decorative effects | Size information: the length of the evil eye room decor is about 29 cm/ 11.42 inch, the appropriate length will not take up too much storage space, light and easy to carry | Bring you beautiful decorative effect: this evil eye door hanging adopts the design of evil eye, flashes behind the rear view mirror together with transparent crystal, and passes through the sun or the light on the roof to bring vitality to your interior environment | Easy to use: these beads are connected in series with strong wires, which are not easy to fall or broken; They are very suitable for hanging in the car, on the wall, on the door and on the mirror to bring you pleasure

★LIGHT WEIGHT. This vintage pilot motorcycle goggles is close to your face and eyes, it will not put pressure on your nose.

|

★HIGH-QUALITY MATERIALS. Imported ABS material, soft sponge frame, high elastic glasses belt, make you feel comfortable.

|

★CLEAR VISION. Made with a PC lens, it is waterproof, dustproof and sturdy, making it safer when driving a motorcycle.

|

★MULTIPLE USES. Suitable for ATV/UTV racing, skiing, motorcycle,cycling competitions, mountain climbing and more.

|

★THE PERFECT GIFT. This goggle can be used as a holiday gift for family, friends and children, etc.

★LIGHT WEIGHT. This vintage pilot motorcycle goggles is close to your face and eyes, it will not put pressure on your nose.

|

★HIGH-QUALITY MATERIALS. Imported ABS material, soft sponge frame, high elastic glasses belt, make you feel comfortable.

|

★CLEAR VISION. Made with a PC lens, it is waterproof, dustproof and sturdy, making it safer when driving a motorcycle.

|

★MULTIPLE USES. Suitable for ATV/UTV racing, skiing, motorcycle,cycling competitions, mountain climbing and more.

|

★THE PERFECT GIFT. This goggle can be used as a holiday gift for family, friends and children, etc.

★LIGHT WEIGHT. This vintage pilot motorcycle goggles is close to your face and eyes, it will not put pressure on your nose.

|

★HIGH-QUALITY MATERIALS. Imported ABS material, soft sponge frame, high elastic glasses belt, make you feel comfortable.

|

★CLEAR VISION. Made with a PC lens, it is waterproof, dustproof and sturdy, making it safer when driving a motorcycle.

|

★MULTIPLE USES. Suitable for ATV/UTV racing, skiing, motorcycle,cycling competitions, mountain climbing and more.

|

★THE PERFECT GIFT. This goggle can be used as a holiday gift for family, friends and children, etc.

★LIGHT WEIGHT. This vintage pilot motorcycle goggles is close to your face and eyes, it will not put pressure on your nose.

|

★HIGH-QUALITY MATERIALS. Imported ABS material, soft sponge frame, high elastic glasses belt, make you feel comfortable.

|

★CLEAR VISION. Made with a PC lens, it is waterproof, dustproof and sturdy, making it safer when driving a motorcycle.

|

★MULTI

★LIGHT WEIGHT. This vintage pilot motorcycle goggles is close to your face and eyes, it will not put pressure on your nose.

|

★HIGH-QUALITY MATERIALS. Imported ABS material, soft sponge frame, high elastic glasses belt, make you feel comfortable.

|

★CLEAR VISION. Made with a PC lens, it is waterproof, dustproof and sturdy, making it safer when driving a motorcycle.

|

★MULTIPLE USES. Suitable for ATV/UTV racing, skiing, motorcycle,cycling competitions, mountain climbing and more.

|

★THE PERFECT GIFT. This goggle can be used as a holiday gift for family, friends and children, etc.

★Vintage Pilot Style Motorcycle goggles designed to fit for half or open face helmets. | ★ABS goggle frame, high rigidity and good chemical resistance. | ★PC lens are scratch-resistant and ultraviolet-proof. | ★Split design, light weight, tinted plastic lenses are scratch resistant | ★Sponge and leather material, soft and comfortable. Super cool style, a necessary goggle for motorcycle drivers.

【Brass Sprinkler Blowout Adapter Kit】: All Brass Dual Purpose RV sprinkler blow out adapter, certified to contain less than 0.25% lead. Durable & Flexible rubber hose more excellent corrosion resistance. | 【17 Inch Rubber Garden Hose】: 17 Inch hybrid rubber blow hose, offers extra strength and durability, allows the adapter to access tight spaces and minimizes stress on pipes and fittings.Max Pressure rating: 300 PSI. Temperature ranging: -22℉ ～ +250℉ | 【Shut Off Valve & Pressure Guage】: This rv winterizing kit comes with adjustable valve and 0-100 psi pressure gauge; You can clearly view the pressure value and adjust the airflow through the valve, no longer need to run to the air compressor to switch. | 【Standard Connection】:Equipped with standard 1/4" air quick plug and 3/4" Female and Male Garden Hose thread, easy attach air line to water lines/hose system to make an nice winterization solution.The quick connector is installed on the pipe with strong thread glue, you will no longer use to worry about air leakage (if you need to remove it, please use a heat gun to heat the plug thread and use a wrench to remove). | 【Wide Application】: Male thread plug generally used to winterize RV, campers, boat, travel trailer, motorhome and personal watercraft. Screw on our additional female-to-female converter to winterize sprinkler systems, outdoor plumbing, irrigation systems and garden hoses.

Movable and Bendable: EXCELFU RV kitchen faucet designed with 360 degree rotatable tap head and flexible arch allow the faucet to rinse the entire sink! It is very easy to move and bend to any spot in the sink and quick to change from a spray to a stream. | Premium Construction: Constructed of stainless steel arch and ABS plastic 8-inch body. Black finish easy to match most sink and easy to clean. | Easy Operation: Classical lever handles with quarter-turn stops for easy operation and easy control of water temperature and flow. | Easy Installation: 1/2 threaded male inlet shanks. Compatible with most standard RV kitchen sink. | Buy with Confidence: Every RV kitchen sink faucet is backed by our friendly and professional Customer Service Team. If there is any questions or suggestion, please feel free to contact with us.

Our 4inch exhaust band clamp are made from high quality 304 Stainless Steel and plating zinc, Can resist the corrosion and rust from water. | Universal fitment, Joins Joins 4" OD Pipe to 4" ID Pipe. Besides, we also provide other different sizes to fulfill your needs. You would better measure before pruchase. | These exhaust clamps feature unitized construction which minimized part number complexity and maximizes material efficiency for reduced weight. | Easy to install, Our joint band clamps is a simple, effective way to connect exhaust system components such as pipes, mufflers and catalytic converters. Unique seal and high clamp loads are provided without distorting your exhaust components, allowing the flexibility to disassemble for service. | NOTE: Please check the size of the prouducts pictures,type and shape to make sure the item is the one that you need.If You Have Any Problems ,Take Time To Contact With Us,We Are In 24 Hours Service !

Our 3inch exhaust band clamp are made from high quality 304 Stainless Steel and plating zinc, Can resist the corrosion and rust from water. | Universal fitment, Joins Joins 3" OD Pipe to 3" ID Pipe. Besides, we also provide other different sizes to fulfill your needs. You would better measure before pruchase. | These exhaust clamps feature unitized construction which minimized part number complexity and maximizes material efficiency for reduced weight. | Easy to install, Our joint band clamps is a simple, effective way to connect exhaust system components such as pipes, mufflers and catalytic converters. Unique seal and high clamp loads are provided without distorting your exhaust components, allowing the flexibility to disassemble for service. | NOTE: Please check the size of the prouducts pictures,type and shape to make sure the item is the one that you need.If You Have Any Problems ,Take Time To Contact With Us,We Are In 24 Hours Service !